Week 6 - Example 7 - Temple Fugures

This is the discussion board for the December 2010 CM 101 Class.
dkrassen
Posts: 106
Joined: Sat Dec 04, 2010 12:03 am

Postby dkrassen » Sun Jan 30, 2011 5:30 pm

Hello.

I had some difficulty with this image.  I selected the gold to make sure that it would not be dimmed.  I used Lab mode with the B channel mask.  What do yo think of it?

Thank you
David
Attachments
20110130_example7-templefugures-lab1_screenshot1-jpg
20110130_example7-templefugures-lab1_screenshot1-jpg (999 Bytes) Viewed 12267 times

dkrassen
Posts: 106
Joined: Sat Dec 04, 2010 12:03 am

Postby dkrassen » Sun Jan 30, 2011 9:21 pm

Hello

I decided to try this image again because I really was not satisfied with my first try.  I sleeted the gold along with the top half of the image.  I then inverted the selection.  I  used the B channel as a mask with some adjustments.  I adjusted the L channel.  Finally, I moved the saturation slider to the left rather than the right (applied some desaturation).  I believe this try is better than the previous one.  What do you think of it?

Thank you
David
Attachments
20110130_example7-templefugures-lab2_screenshot1-jpg
20110130_example7-templefugures-lab2_screenshot1-jpg (173.38 KiB) Viewed 12267 times

ggroess
Posts: 5342
Joined: Wed May 24, 2006 2:15 am
Contact:

Postby ggroess » Sun Jan 30, 2011 9:30 pm

David,
While B is a good choice for this image you can get even further by looking at the saturation mask.  Apply a light to medium blur using the mask commands in CM.  Start by balancing the exposure over the two halves of the image.  Then adjust the saturation using the LAB slider. 

Give it another try...

Greg

dkrassen
Posts: 106
Joined: Sat Dec 04, 2010 12:03 am

Postby dkrassen » Sun Jan 30, 2011 9:50 pm

Hello.

You suggest a blur under the mask command.  There are four options for blur; (1) none, (2) light, (3) medium and (4) wide.  Please explain exactly what each option for blur under mask performs?

Thank you
David

ggroess
Posts: 5342
Joined: Wed May 24, 2006 2:15 am
Contact:

Postby ggroess » Sun Jan 30, 2011 9:54 pm

It adds a light Gaussian blur to the mask in pixels.  I'll see If i can find the exact number of pixels that it blurs....
This allows the transition from masked area to unmasked to be gradual and help hide the mask from the viewer.

Greg

mikemeister_admin
Posts: 4927
Joined: Fri Sep 20, 2013 8:29 pm

Postby mikemeister_admin » Sun Jan 30, 2011 10:08 pm

I found that it was very instructive just to try the different levels of blurring to see what it would give on the masks that I developed.

Richard

ggroess
Posts: 5342
Joined: Wed May 24, 2006 2:15 am
Contact:

Postby ggroess » Sun Jan 30, 2011 10:53 pm

I'm thinking it is 1, 8 and 10 for the Blur values...Mike if you are watching can you confirm?

Greg

dkrassen
Posts: 106
Joined: Sat Dec 04, 2010 12:03 am

Postby dkrassen » Sun Jan 30, 2011 10:59 pm

Hello

I decided to re-do this image.  This time I used the S channel as a mask with blur set to wide.  I believe this is the best one so far.  What do you think of this image?

Thank you
David
Attachments
20110130_example7-templefugures-schannelmasklab3_screenshot1a-jpg
20110130_example7-templefugures-schannelmasklab3_screenshot1a-jpg (43.99 KiB) Viewed 12267 times
20110130_example7-templefugures-lab3_screenshot1b-jpg
20110130_example7-templefugures-lab3_screenshot1b-jpg (169.18 KiB) Viewed 12267 times

ggroess
Posts: 5342
Joined: Wed May 24, 2006 2:15 am
Contact:

Postby ggroess » Mon Jan 31, 2011 12:15 am

I think it is much better and you can still open the shadows and mid-tones as shown...
Then if you add some saturation you have it...

Greg
Attachments
screenshot004-jpg-3
screenshot004-jpg-3 (252.62 KiB) Viewed 12267 times


Return to “Curvemeister 101 - December 2010”

Who is online

Users browsing this forum: No registered users and 6 guests